How To Turn Off Gas Water Heater Pilot Light

If you only want to turn off the heater for a few minutes for servicing, turn the dial to pilot. Turn the gas knob to “pilot,” press and hold it down.

Products from Energy Solar heating, Domestic

First locate the temperature controls.

How to turn off gas water heater pilot light. Take the panels of the water heater so you can reach the pilot light wherever it is located. If you have trouble locating it, it’s usually located at the front of the water heater. There are timers that automatically turn on/off the water heater depending on the need at hand.

The pilot light starts after the igniter sparks, which causes this flame to activate the water heater. A pilot light is a small device that is designed to provide the flame and light the gas coming out of the gas valve and main burner. Turn the gas control knob to pilot and press it downward.

Now off the regulator valve. Steps to relight the pilot light. This is where we can move on and check the interior door panel for the directions to find out how to turn on gas water heater pilot light.

Dirty or dusty pilot light burner. The short and sweet answer: Shut off the gas valve.

This shuts off the pilot as well as preventing the burner from igniting. Remove the burner access covers and unscrew the nuts on the gas, pilot and thermocouple lines. Turn off the control valve.

Also, is it dangerous if the pilot light goes out on water heater? It is common on fireplaces and older/cheaper furnaces and water heaters. The pilot light is the small flame fueled and lit by a gas burner at the base of your water heater.

Typically, this will be under the gas valve. Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit. Turn the switch for the pilot light so it is on the pilot position.

Here are some critical reasons why. Push down the red button to the left of the gas knob. Pull out the water heater pilot light burner.

Make sure to remove out the outer and the inner panel to access out the light of the panel. Generally leaving your water heater system on a pilot mode even for 3 weeks will not cause leakage. The pilot mode can help you to detect if there is any leakage of gas in your system.

The guaranteed issue will be that your water heater will take a long time to heat the tank water back up. This is the only way to make sure the gas is reaching the pilot light. As we’ve mentioned before, pilot light is a necessary part of a gas water heater.

Some water heaters just have an open gap instead where you can see the pilot light burner. Turn the dial past the pilot position to the off position. Hold the pilot’s button and then make sure to use the long lighter or a match to ignite the flame.

A handle parallel to the pipe indicates an open valve. A pilot light is always burning while using a small amount of gas, either a water heater is running or not. The thermocouple is a device on the gas heater that senses the pilot’s heat and feeds it gas.

Make sure the line valves are open. Make sure to turn the thermostat to the lowest setting. Use a flashlight or a headlamp to find the burner inside.

Reset the thermostat so it is on the lowest setting possible. When the thermocouple is functioning properly, the gas is cut off on its own. No, you should not turn off your water heater when on vacation.

Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. Open the door/cover over the pilot light access. How to light a water heater pilot light.

This will be located under the gas valve; Your gas release or electric heating element is malfunctioning. Some units, there will be difficulties to turn it on again, lighting a pilot light comes to mind for gas powered water heaters.

The knob should be clearly labelled. If you find your water not warm enough while on a pilot mode, then there will be a problem with your system. Hold down the pilot button or the ignite button.

Open the door/cover over the pilot light access. Turn out the on/off switch of the pilot towards a pilot’s position. The pilot light will be cut if it’s malfunctioning because then it will cut the gas to the pilot.

We want to put the heat to the minimum. Check to make sure that the water heater has turned off. You may hear a slight hiss.

If the gas supply is blocked, or if the amount of gas isn’t sufficient, the pilot light won’t stay lit. While still holding the gas down, light that pilot. Hold a lighted match to the pilot — a long fireplace match.

Find the pilot light access. If it senses that the pilot light has gone out, the thermocouple shuts off the gas supply to the flame in order to prevent safety issues with your water heater. This gas flame heats up the metal pipe inside your water heater which heats up your water, but like any common lighter or grill igniter, you need both flame and gas for the light to stay lit.

If there is no release of any combustion agent, the pilot light will fail to start. Turn the knob to “off,” and then wait five minutes for the gas to clear before you follow these steps: This will start the flow of gas to the pilot.

Gas water heaters need to have a flow of gas to the pilot light in order to remain working. When the flame ignites, continue to hold the gas knob or button down for a full minute. Open the cover to the pilot (if one is present) and look inside the opening with the help of a flashlight.

If You Know These Things You’re a Genius Homeowner Home