How To Change Code On Door Lock Weiser

The lock beeps, the keypad ﬂ ashes red, and the door cannot lock or unlock. Enter user code to be deleted.

Keyless Entry Door Lever Door levers, Keyless door lock

Keep holding the button for 30 seconds until the lock beeps

How to change code on door lock weiser. Manufacturer’s installation guide important installation steps 1. Press the program button once more. Using the weiser app within bluetooth range, you can lock/unlock the aura smart lock and program up to 250 user access codes that can be scheduled and.

If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock. Insert the exterior (keyed) side of the lock through the exterior side of your door. Call technical support for further troubleshooting.

The bolt should retract to the unlocked position. Press the “lock” button to save code. Prepare the door and check dimensions.

If you have an old weiser lock that does not have the smart key feature, you'll have to remove the lock from the door to rekey it. Just pull off the top back cover of the unit and you will find the simple step by step instructions on how to change the combination on the inside of the cover. Locked turnbutton the turnbutton cannot rotate.

For example, if you want to delete the third code, add a diff erent user code in position three. Smart door lock (weiser smartcode 10 touchpad electronic deadbolt) 2. On the touchpad, select the settings app from the home screen.

6 press lock button once. Fl ash fi ve times and you will hear fi ve beeps. You should see the schlage button turn green, giving one long flash and one long beep.

Hold these two units in place, then insert screws into the interior side of the lock to fasten it to the door. Consequently, how do you change the code on a kwikset door lock? Fl ashes green (about 5 seconds).

Test code while the door is open, test the user code to make sure it no longer unlocks the door. Make sure the user code is correct and that the lock button is pushed after entering the user code. Press the 1 button and wait for the same three lights and three beeps.

When the led flashes green, the lock has been reset. Press and hold the program button until the keypad 4. With auto lock enabled, smartcode will automatically relock the door

Programming the 2nd user code. Please install one smart door lock at a time. Measure to con irm that the hole in.

Enter the code to unlock: 38 mm (1 1/2 in). Pair the smart door lock to your rogers smart home monitoring system using this guide.

The door is now unlocked! Hope this helps, i'd been wondering about it myself for a lonnngg time :) Smartcode at a glance deleting a single user code

Once the smart door lock has been physically installed and tested for proper functioning, follow the steps below to pair your smart door lock with your rogers smart home monitoring system. The door can be locked with the lock button, but the user code will not unlock the door. After typing in the last 4 digits of your phone number click change lock code and type in the new lock code you would like.

This process will only work if your weiser lock is installed on the door and the door is shut. Wait a moment for the three lights and three beeps to repeat. For instuctions on how to add user codes when the mastercode is disabled, see the installation and user guide that came with your lock.

2 press lock button once. Door jammed while attempting to lock relock door. To start over, touch the lock button to lock the door.

Enter in 4 to 8 digit code onto the keypad. Switch #2 enables the auto lock when in the on position. 4 press lock button once.

Install the smart door lock using the manufacturer’s installation guide provided in the box. If you're looking for answers, information and resources to help. Enter in 4 to 8 digit code onto the keypad.

Page 5 62812 / 01 deleting a single user code with the mastercode enabled 1. If drilling a new door, use the supplied template and the complete. Code to teach the lock the orientation of the door:

Find all the resources to help with your weiser product and installation needs. Man installing a door lock on a white door. Procedure continued on next page 4 / 15 62810 / 01 usa:

If the door still won’t unlock, use a key to unlock the door. Reference guide exterior back panel. This is something most homeowners quite often forget to do.

When the door is closed and the lock. Press the program button once. The door is either 54 mm (2 1/8 in) or.

Enter the access code to unlock: Press the program button on the interior unit three times. Press the “lock” button to save code.

Pair with smartthings [found information on how to put the lock into pairing mode by following [ref 4] pairing the smart door lock with your touchpad”] Just go through all the possible combinations and unlock it (only if its a 3/4 digit) on the other hand if you do know the code and want to change the lock, hold down the unlock button/lever and change the digits and that should change the code. If it does not unlock, repeat steps (a) through (c).

Page 6 62816 / 01 troubleshooting: Press the program button twice, enter the same or a new code and then press the lock button once. Test the old user code to make sure it can no longer unlock the door.

If unsuccessful make sure to enter the same valid code in steps 3 and 5. Insert the key into the lock and turn it slightly more than half a turn while pulling the cylinder tailpiece through the back of the lock. 3 enter user code to be deleted.

Press and hold the program button while reinserting the battery pack. Line up the connecting rods and cylinder tailpiece to insert the interior trim. Door drilling instructions available at www.weiserlock.com/doorprep.

If your old code still remains in the unit, you will need to perform a hard reset of the unit.

Electronic Digtial Lock, Keyless digital Safe Lock Door